Est. 1980 • 35+ years • Marlette, Michigan
Keep your herd on all fours.
Square-edged concrete grooving that stops slips before they become lameness. We don't sell grooves — we keep your cows on their feet and out of the lameness column.
- 35+ years
- Dairy, beef & goat barns
- Traveling crews nationwide
- Fair, flat pricing
The problem
A slip today becomes a lame cow tomorrow
Smooth barn floors don't just slow cows down — they put animals in the lameness column, drain milk production, and force culls you didn't plan for.
$4.5
Per lame cow, per day
Estimated industry average
700–900 lbs
Milk lost per lactation
Estimated per lame cow
$76–$533
Cost per lameness case
Lameness is the #3 cost on a dairy farm
All figures are industry estimates for planning purposes. Actual costs vary by herd, management, and severity. See the full economics →
Equipment
One Machine. Every Pattern.
Davidson runs professional EDCO diamond-blade grooving saws with interchangeable blade gangs and adjustable spacing. A single machine — with a blade swap and a change of pass angle — cuts straight lines, the tractor (herringbone) pattern, or a full diamond, matched to each barn area.
The equipment is why we can do it all — and keep our pricing fair.
Alleys & single-direction traffic
Ramps, slopes, maximum grip
Turns, holding areas, all-direction traction
Proof on the floor
Diamond at the turn. Tractor down the alley.
Same EDCO saw, same crew — we swap blade gangs and pass angle to match each zone. No second contractor. No inflated quote.
Davidson Cement Grooving, Inc.
Same crew, same machine — two patterns in one job.
Diamond for the turn. Tractor for the slope. One pass setup — blade swap and angle change, not a second crew.
On-site proof
See the process before we arrive
Watch our crew, equipment, and grooving patterns in action — the same EDCO diamond-blade process that keeps dairy, beef, and goat barns across the country on solid footing.
Results
Before & After
Drag the slider to compare worn barn floors against freshly grooved traction surfaces.
Worn-smooth concrete → freshly grooved
Wet, muddy ungrooved alley → clean grooved alley
Manure-packed worn grooves → sharp fresh grooves
Scrapers and manure wear grooves smooth in 6–8 years — we restore traction in a day.
Cost of slipping
What is lameness costing your herd?
Adjust the numbers below. All outputs are estimates based on industry averages — your actual costs may vary.
Industry range is often 15–30%. Default: 25%.
Barn area estimated at 15 sq ft/cow (3,000 sq ft total). Grooving at ~$0.75/sq ft.
$82,125
Estimated annual lameness loss
50 lame cows × $4.5/day × 365
$2,250
Estimated one-time grooving cost
Based on barn area estimate above
~1 months
Estimated payback period
~$408,375 estimated 5-year savings vs. doing nothing
Proper grooving pays for itself fast when you factor in lost milk, treatment costs, and culls. These are estimates — not guarantees.
Services
Grooving for every high-traffic area in your barn
From alleys to parlors to turn lanes — we cut square-edged grooves where your cows need traction most.
Pattern gallery
See the grooves before we cut
Straight lines, tractor herringbone, diamond turns, and textured surfaces — every pattern matched to where your cows walk.
Where we work
Every high-traffic surface in your barn
From freestall alleys to parlor returns and outdoor barnyards — we groove the concrete your cows walk on every day.
Freestall barn — full-scale grooving
Alleys
Holding areas
Parlor returns
Ramps
Barnyards
Our standard
Why our grooves are different
We cut square-edged grooves at research-backed spacing — the MSU / UW–Madison Dairyland Initiative standard. Done wrong, grooving abrades hooves. That's why 35 years of experience matters.
Correct — Square-edged groove
Clean 90° edges at MSU / UW–Madison Dairyland Initiative spacing. Provides traction without excessive hoof abrasion.
Wrong — Worn V-groove
Worn or improperly cut V-grooves abrade hooves and lose traction. This is what gives grooving a bad name — and why experience matters.
Comparison
Grooving vs. traction milling
You've heard the pitch that milling is the future. Here's the calm, factual comparison — no sales games.
| Square-edged grooving | Traction milling | |
|---|---|---|
| Traction | Square-edged grooves — proven standard when properly cut and maintained | Aggressive initial texture that can fade unevenly |
| Maintenance | Regroove every 6–8 years as edges wear | May require re-treatment; texture degrades unpredictably |
| Hoof abrasion risk | Low when grooves are square-edged and at proper spacing | Higher abrasion risk if surface is too aggressive or uneven |
Pricing
Fair, flat pricing — no games
Roughly $0.75/sq ft from a 35-year crew — often about half what traveling competitors charge. Varies by floor condition, size, and pattern. Volume jobs across the whole barn or multiple sites bring the best value.
~$0.75/sq ft
We frame it as honest, fair pricing from people who've done this for decades — not as a discount or budget option. When you groove the whole barn or multiple sites at once, the value adds up even faster.
Get your free estimate35+
Years in business
Millions
Sq ft grooved
Nationwide
Traveling crews
Social proof
What farm managers say
Placeholder testimonials — replace with real quotes in site-config.ts
Service area
We travel to all 50 states except Hawaii & Alaska
All 50 states except Hawaii & Alaska
48 states + DC
We travel nationwide for barn floor grooving
All 50 states except Hawaii & Alaska
Based in Marlette, Michigan, our traveling crews groove barns nationwide. From Texas dairy country to Wisconsin freestalls — if the job is big enough, we'll get there.
View full service area →Maintenance
Floors wear smooth every 6–8 years — we'll remind you before your cows do.
Concrete grooves wear smooth every 6–8 years. Join our reminder list and we'll reach out before traction drops and lameness climbs.
Ready to keep your herd on all fours?
Get a free estimate from a crew that's been grooving barn floors for 35+ years. Fair price, no games.